Hallo Forum,
ich habe mich heute hier angemeldet weil mein LTE Router nicht will.
Seit letzter Woche versuche ich das Ding zum Laufen zu kriegen bekomme aber immer Fehlercode 6.
5 Anrufe bei der Hotline haben nichts gebracht, ausser dass es jetzt gehen müsste weil die Freischaltung erfolgt ist.
Nachdem ich hier gelesen habe, dass man unter APN internet.home eingeben soll sind aus 3 BLOCK's einer geworden.
Hier die Diagnosedatei ...
~~~~~~PC Information~~~~~~
001 OS Name: Windows NT 6.1 PASS
002 Browser: MSIE 9.0 PASS
~~~~~~Product Information~~~~~~
003 Model: B390s-2 PASS
004 Software Version: V200R001C108SP22 PASS
005 Hardware Version: B390-B390RW2A Ver.C PASS
006 SN: 4UA5TC9272500817 PASS
007 IMEI: 354637042112244 PASS
008 LAN MAC Address: 88:53
4:2E:AF:2A PASS
009 WLAN MAC Address: 88:53
4:2E:BA:7E PASS
010 Check AT-Port: Available PASS
~~~~~~LTE State~~~~~~
011 Dialing Mode: Auto PASS
012 APN: internet.home PASS
013 DNS: N/A BLOCK
014 PDN Type: IPv4 PASS
015 Service Status: NO Service PASS
016 Connection Status: Connection Failed.Error Code:6 PASS
017 Frequency: 816000 kHz PASS
018 Bandwidth: 10MHz PASS
019 CellId: 212 PASS
020 IP Address: 0.0.0.0 PASS
021 RSRP: -91dBm PASS
022 RSSI: -67dBm PASS
023 RSRQ: -7dB PASS
024 Roam: N/A BLOCK
025 Antenna State: Built-In PASS
~~~~~~DHCP~~~~~~
026 Gateway IP Address: 192.168.1.1 PASS
027 DHCP Enabled: true PASS
028 Subnet Mask: 255.255.255.0 PASS
029 DHCP_ip_pool_start: 192.168.1.2 PASS
030 DHCP_ip_pool_end: 192.168.1.254 PASS
031 DHCP_lease_time(s): 86400 PASS
~~~~~~SIM/PIN State~~~~~~
032 sim_state: SIM Card detected PASS
033 PIN code: READY PASS
~~~~~~WiFi Parameters~~~~~~
034 SSID: WLAN-00774A PASS
035 Channel: 6 PASS
036 WLAN Switch: Enabled PASS
037 AuthMode: WPA2-PSK PASS
038 EncryptionModes: AES PASS
Für Hinweise woran es liegen könnte wäre ich sehr dankbar ...
Harald
ich habe mich heute hier angemeldet weil mein LTE Router nicht will.
Seit letzter Woche versuche ich das Ding zum Laufen zu kriegen bekomme aber immer Fehlercode 6.
5 Anrufe bei der Hotline haben nichts gebracht, ausser dass es jetzt gehen müsste weil die Freischaltung erfolgt ist.
Nachdem ich hier gelesen habe, dass man unter APN internet.home eingeben soll sind aus 3 BLOCK's einer geworden.
Hier die Diagnosedatei ...
~~~~~~PC Information~~~~~~
001 OS Name: Windows NT 6.1 PASS
002 Browser: MSIE 9.0 PASS
~~~~~~Product Information~~~~~~
003 Model: B390s-2 PASS
004 Software Version: V200R001C108SP22 PASS
005 Hardware Version: B390-B390RW2A Ver.C PASS
006 SN: 4UA5TC9272500817 PASS
007 IMEI: 354637042112244 PASS
008 LAN MAC Address: 88:53
009 WLAN MAC Address: 88:53
010 Check AT-Port: Available PASS
~~~~~~LTE State~~~~~~
011 Dialing Mode: Auto PASS
012 APN: internet.home PASS
013 DNS: N/A BLOCK
014 PDN Type: IPv4 PASS
015 Service Status: NO Service PASS
016 Connection Status: Connection Failed.Error Code:6 PASS
017 Frequency: 816000 kHz PASS
018 Bandwidth: 10MHz PASS
019 CellId: 212 PASS
020 IP Address: 0.0.0.0 PASS
021 RSRP: -91dBm PASS
022 RSSI: -67dBm PASS
023 RSRQ: -7dB PASS
024 Roam: N/A BLOCK
025 Antenna State: Built-In PASS
~~~~~~DHCP~~~~~~
026 Gateway IP Address: 192.168.1.1 PASS
027 DHCP Enabled: true PASS
028 Subnet Mask: 255.255.255.0 PASS
029 DHCP_ip_pool_start: 192.168.1.2 PASS
030 DHCP_ip_pool_end: 192.168.1.254 PASS
031 DHCP_lease_time(s): 86400 PASS
~~~~~~SIM/PIN State~~~~~~
032 sim_state: SIM Card detected PASS
033 PIN code: READY PASS
~~~~~~WiFi Parameters~~~~~~
034 SSID: WLAN-00774A PASS
035 Channel: 6 PASS
036 WLAN Switch: Enabled PASS
037 AuthMode: WPA2-PSK PASS
038 EncryptionModes: AES PASS
Für Hinweise woran es liegen könnte wäre ich sehr dankbar ...
Harald